To close this particular build off, the Road van is lettered, although I cannot take credit for the fine job on the lettering, it was done by its new owner.
This shot was taken part way through the process

All lettered up and ready for the ‘road’

To close this particular build off, the Road van is lettered, although I cannot take credit for the fine job on the lettering, it was done by its new owner.
This shot was taken part way through the process
All lettered up and ready for the ‘road’
The Road van was painted at the same time as the brake vans but I held off posting photos because they formed part of the GOG virtual show’s lockdown models display. The show was held today so I am not taking anything away from it by adding them to my threads.I enlisted Chris’s help to paint the curved arrows on the plate above the brake hand wheel
Finally I was asked by a friend to take photos of both bogie vans together.
For those not familiar with it the LMS van is the Dragon Models Lancashire and Yorkshire 30 ton Bogie van now with TaffVale Models.
And finally, the roof “canvas” is added along with a couple of the plates that adorn each side of the van were knocked up from scrap etch.
Next stop the spray booth.
I have had a few of Dan’s kits over time and one thing that I find odd is that some come with roofs and some come without. Sadly, the road van came without (yet an NER horsebox that I bought at the same time had one). I can only guess that it depends on whether Dan has roof material to hand when he packs the kit.
A suitable piece of sheet was obtained and cut to size. It was just too long for either of my sets of rolling bars so I had to resort to rolling it by hand but I got there in the end.
When built these vans were fitted with sliding roof hatches over the left hand set of doors on each side. Later these were replaced with canvas or just boarded over so lots of permutations are possible depending on the period being modelled. This van was to have roof doors so I cut an offcut of thicker brass sheet to size (my guillotine needed a bit of muscle to cut through it). This time it did go through the rolling bars…
The photos that I have seen with roof hatches had a curved strip across them which is possibly a rainstrip? I represented this with a short length of 1mm square rod.
The roof was still loose at this point.
The kit does provide the runners in the form of whitemetal castings so these were duly soldered on. And finally the roof was soldered on to the body.
I had got this far, then while studying photos noted that there was a turnbuckle in the middle truss rod. I made some up using tube and 14ba nuts and then cut the truss rod to allow them to be eased aside and slipped on.
I forgot to add in the last post that the Couplings, vac and Westinghouse pipes are Laurie Griffin.
The kit comes with nice cast brake cylinders which have cast on mounting brackets. The odd thing is that they come with a separate domed end but you can’t fit them unless you make the mounting brackets longer. I elected to file them off and replace them with brass strip. This makes them sit a bit lower and I had to put a slight bend in the brake rods to get them to pass over the cylinder.
With it being quite a long van, I added some supports for the middle of the roof from scrap etch.
Almost before adding much more under frame detail I couldn’t resist trying the bogies underneath it for an idea of how the finished van would look.
The outer truss rods are quite interesting on that they have two rod one on the outside and the second on the inside of the solebar. The instructions have you add these in two pieces I did them in one with a square U bending in the middle. This proved a bit tricky to get sitting right on the front face and I suspect that doing it in two pieces wouldn’t have proved equally tricky.
Moving rapidly on with the Road van body, the instructions suggest that you fit the ends first and once I filed of an offending etching cusp, the ends fit nicely.
My recently acquired RSU has come into its own on this build. Using it allows me to use the probe to hold pieces in place while tacking them. After tinning the edges of the ends, sides and the fold down on the floor pan, tacking it together with the RSU became a breeze. I ran the microflame gently down the joints to join up the dots and hey presto.
It may just be me but it seemed so much easier than my previous efforts with van bodies. In fairness, the kit is well designed and that helps too.
Before going any further I took the time to detail the sides while they were flat. One of the features that I love about many North Eastern Railway vans is the doors and their variations of the locking mechanisms.
Much of this detail is provided in the etches and I only added the locking rods and some thin half etched strip to create the staples that the locking rods and lower locking bar fit into.
Once the various grab handles and pins for the drop doors were added they were ready for fitting.
Like many I suffered a bit of a mojo loss recently so I decided to take a short break from loco building to tackle a couple of wagons in the hope that the enthusiasm was rekindled.
The first of these is a D&S Kit for a North Eastern Railway Bogie Road Van. Although I have had one of these kits for about 3 years, this one is for a gent who lives in Scotland who models the North Eastern Railway so I rang Dan Pinnock to enquire as to availability last year. Dan said he could do a kit but he would have to order the etches.
And so, onto the build.
I started with the basic floor pan and solebars. Like many kits the floor pan has fold down strips down the long edges. what is unusual is that these are not the solebars. The solebars have a full thickness rear section and a half etched overlay. The rear has a narrow fold along the bottom edge to represent the C section of a steel solebar. When put together the solebars fit into slots behind the fold down strips on the floor pan. To this floor pan is added a pair of queen posts
Next, I made up the bogies, these are simple in design. A pair of really nice brass castings fit onto the ends of a fold up central bolster. Each bolster has a fold up strip on the top which either allows for and aft rocking or side to side.
The brakes are simple affairs which fit nicely between the wheels on each side.